OEM vfd 5 Hp 460v 220v Single Phase manufacturer

The control core of the ZYV6 AC drive is based on a 32-bit RISC microcontroller. Its operation speed can complete efficient and complex motor control algorithms. It perfectly combines vector control and VF control technology to improve load torque response in a timely manner to meet customers' wide range of variable torque loads need.

Power range 0.75kW~200kW
Voltage level AC 1PH/3PH 220V
AC 3PH 380V

Model Description

Features

Technical Parameters

ZYV6-7R5G-011P-4omi

●Has advanced open-loop vector control performance and good voltage and current control technology;

●Starting torque: 0.5Hz/150% torque;

●Wide voltage range design, the wide voltage range reaches AC 3PH: 360V～450V;

●Inverters below 18.5kW (inclusive) have built-in braking units;

●Has the function of not shutting down in case of instantaneous power failure;

●Independent air duct design supports wall-mounted and floor-standing installation methods, providing customers with a more reliable and economical installation and use method.

Project			Technical Parameters
Enter	Rated voltage		3PH AC 380V
	Frequency		50Hz/60Hz
	Voltage allowable variation range		3PH AC 360V~450V
Output	Voltage		0~440V
	Frequency		Low frequency mode：0~300Hz High frequency mode：0~3000Hz
	Overload capacity		G type machine: 110% long term; 150% 1 minute; 180% 1 second P type machine: 105% long term; 120% 1 minute; 150% 1 second
Control characteristics	Control method		0: Ordinary V/F control; 1: Advanced V/F control: 2: Open-loop current vector control; 3: Separate V/F control
	Modulation		Space voltage vector PWM modulation
	Starting torque		150% rated torque at 0.5Hz (vector type V/F control)
	Frequency accuracy		Digital setting: maximum frequency´+0.01%; analog setting: maximum frequency´±0.2%
	Frequency resolution		Digital setting: 0.01Hz；Analog setting: Maximum frequency´0.05%
	Torque boost		Automatic torque boost, manual torque boost 0.1% to 30.0%
	V/F curve		0: Linear curve 1: Decreasing torque curve 1 (1.3 power) 2: Torque reduction curve 2 (1.5 power) 3: Torque reduction curve 3 (1.7 power) 4: Square curve 5: User-set V/F curve
	Acceleration and deceleration curve		Three methods: linear acceleration and deceleration, S-curve acceleration and deceleration, and shortest acceleration and deceleration; Four acceleration and deceleration times, time unit (minute/second) optional
	DC braking		Stop DC braking starting frequency: 0.00Hz~maximum output frequency; Braking time: 0.0~50.0s; Braking current: 0.0%~150.0% rated current
	Automatic voltage regulation (AVR)		When the grid voltage changes, it can automatically keep the output voltage constant
	Automatic current limit		Automatically limit the current during operation to prevent frequent overcurrent fault tripping
	Automatic carrier adjustment		Automatically adjust carrier frequency according to load characteristics and temperature characteristics
Run function	Run command channel		The operation panel, control terminal and serial port can be switched in a variety of ways.
	Frequency given channel		Digital given, analog voltage given, analog current given, pulse given, serial port given, terminal given, multi-speed given, can be switched in a variety of ways
	Auxiliary frequency given		Realize flexible auxiliary frequency fine-tuning and frequency combination calculations
	Pulse output terminal		0~50kHz pulse square wave signal output, which can realize the output of physical quantities such as set frequency and output frequency.
	Analog output terminal		2 analog signal outputs, each optional 0/4~20mA or 0/2~10V, can realize the output of physical quantities such as set frequency and output frequency.
Operation panel	LED display		Can display 61 parameters such as set frequency, output frequency, output voltage, output current, etc.
	Button function selection		Define the scope of some keys to prevent misoperation
Protective function			Phase loss protection (optional), overcurrent protection, overvoltage protection, undervoltage protection, overheating protection, overload protection, load loss protection, etc.
Environment		Place of use	Indoor, no direct sunlight, no corrosion, no flammable gas, no oil mist, dust, etc.
		Ambient temperature	-10℃~＋40℃（The ambient temperature is between 40℃ and 50℃, please derate it for use.）
		Ambient humidity	5%~95%RH，No water droplets condensation
		Altitude	Derate for use above 1000 meters, and derate by 10% for every 1000 meters.
Structure		Protection level	IP20
		Cooling method	Air-cooled, with fan control
Installation method			Wall-mounted, cabinet type